UMG 96-PA-MID+CH 90...277 V AC, 90...250 V DC

4-in-1 energy management: | power quality monitoring | RCM monitoring | MID certification:

The UMG 96-PA energy measurement device can combine four functions in one device and can be modularly extended by two analog inputs - either as 0-20 mA analog inputs (e.g. DC measurement) or as RCM measurement inputs with cable break detection and additional temperature measurement. It is also MID certified and approved for active energy billing purposes:

Energy management system

- Continuous energy monitoring

- Identification of potential savings

- Reduction of energy costs

- Compliance with tax and regulatory requirements

Power quality

- Secure, highly available power supply

- Avoidance of production downtime

- Maximize uptime / preventive maintenance

- Avoidance of quality defects in the product

Residual current monitoring (RCM)

- Permanent monitoring of residual currents

- Supports fire and personal protection

- Reduced effort for DGUV V3 testing

- Increased system availability

General:

 Measuring accuracy for voltage, current 0.2%

 Measuring accuracy for active energy (kWh, .../5 A) class 0.2S

Supply voltage:

 AC 90 V - 277 V (50/60) Hz or DC 90 V - 250 V, 300 V CAT III

Inputs and outputs:

 3 digital inputs and outputs each

 1 analog output

RMS value measurement - instantaneous values, e.g:

 Current, voltage, frequency

 Active, reactive and apparent power

 Power factor

Energy measurement:

 Active, reactive and apparent energy

 Tariffs: HT / NT

Ambient conditions:

 Temperature range, operation: K55 (-10 ... +55 °C)

Acquisition of average values, e.g:

 Voltage, current / current and maximum

 Active, reactive and apparent power / current and maximum

 Frequency / current and maximum

Measurement of the voltage quality:

 Harmonics per order / current and voltage: 1.-40.

 Distortion factor THD-U /THD-I in %

 Current and voltage, zero, positive and negative sequence

Measurement data recording:

 4 MB memory (flash)

 Average, minimum and maximum values

Interface / protocol:

 RS485 / Modbus RTU

Programming / limit values / alarm management:

 Comparator (2 groups with 3 comparators each)

Grid visualization software

 Free GridVis Essentials

Optional additional functions with the GridVis Standard and Expert packages

Measurement voltage input (3 x):

 Overvoltage category: 600 V CAT III

 Measuring range, voltage L-N, AC (without transformer): 0 ... 600 Vrms (± 10%)

 Measuring range, voltage L-L, AC (without transformer): 0 ... 1040 Vrms (± 10%)

 Frequency measuring range: 45 ... 65 Hz

 Sampling frequency per channel (50 / 60 Hz): 8.33 kHz

 Measurement in quadrants: 4

 Networks: TN, TT

Measuring current input (3 x):

 Rated current: 1 / 5 A

 Overvoltage category: 300 V CAT II

 Sampling frequency: 8.33 kHz

Mechanical properties:

 Protection class according to EN 60529 (with seal = IP54): Front IP40 / Rear IP20

 Mounting according to IEC EN 60999-1 / DIN EN 50022: Front panel

Installation:

Built-in device, 96 x 96 x 86 mm (WxHxD)

Supply voltage: 90 - 277 V AC

Installation category: 300 V CAT III

Accessories (included):

 Installation instructions

 Safety instructions included

 Mounting kit

 RS485 terminating resistor 120 Ohm

Observe installation position and minimum distances according to installation instructions:

 Top/bottom 50mm distance

 Lateral distance 20mm